Notes On the Use of Silicon Steel Sheet Cross-Cutting Line
The cross-shear line is used for uncoiling, leveling, sizing and shearing of metal coils into flat sheets of required length and stacking.
It is suitable for processing cold-rolled and hot-rolled carbon steel, silicon steel, tinplate, stainless steel and all kinds of metal materials after the surface coating cross-cutting operation.
That we are operating silicon steel sheet cross shear line what are the basic requirements?
Basic requirements: silicon steel shear line operators should have a high degree of mechanical and electrical knowledge, and after automatic control (CNC) training, qualified by the examination to obtain "cross-cutting line safety operation certificate" before they can work independently. The operator of the silicon steel shear line must participate in the safety training for heavy lifters (including the use of cranes and spreaders) and pass the test to obtain the "safety certificate for heavy lifters".
Silicon steel cross-cutting line using the preparatory work.
1, Open the air supply, when the air pressure to 6 Pa will open the drain valve drainage, water exhausted, before you are ready to start the machine.
2, Check the amount of oil in the oil mist, the amount of oil should be between 1/3-2/3 of the oil cup, the shortage should be supplemented. Be sure to turn off the air source and evacuate the compressed air when replenishing the oil amount.
3, Lubricate the guide rail and screw, and wipe it clean with oil.
4, Start the power trial, check whether the sensors are normal, fastening bolts are safe and reliable.
Silicon steel sheet cross-cutting line using the working process.
1, Carefully and carefully read the drawing, enter the sheet width, sheet length and other data as required and review. Adjust the width of the guide rail, the position of the punching machine and the position of the stacking table according to the requirements.
2, Measure the actual width of the silicon steel coil to be cut, the measurement accuracy is 0.05 mm, check the width tolerance of the coil, S degree and waviness, all shall not exceed the standard.
3, On the material, manual trial shear, take the piece, compared with the drawings by checking the qualified before automatic shear.
4, Shear process operators to pay close attention to the transmission parts of the operating conditions, once the phenomenon of jamming, immediately stop to deal with.
5, The normal working process of the equipment, arms and other parts of the body do not reach into the pile of material under the table and other parts of the transmission, to prevent accidents, if necessary, adjustments should be made in the shutdown state.
6, Do not place tools, material pieces and other miscellaneous objects on the equipment when the equipment is running.
7, When using the crane to get on and off the material rolls, be sure to operate according to the regulations, to prevent accidents.
8, When lifting finished products, make sure to adjust the balance of the material table, start slowly and fall slowly to prevent injuries from slippery pieces.
9, The waste basket should be replaced in time when the waste is full.
10, During the work, if the equipment is abnormal, stop immediately, notify the equipment maintenance personnel, and make a record.
11, Fill in the handover record carefully when handing over the shift.
That we are operating silicon steel sheet cross shear line what are the basic requirements?
Basic requirements: silicon steel shear line operators should have a high degree of mechanical and electrical knowledge, and after automatic control (CNC) training, qualified by the examination to obtain "cross-cutting line safety operation certificate" before they can work independently. The operator of the silicon steel shear line must participate in the safety training for heavy lifters (including the use of cranes and spreaders) and pass the test to obtain the "safety certificate for heavy lifters".
Silicon steel cross-cutting line using the preparatory work.
1, Open the air supply, when the air pressure to 6 Pa will open the drain valve drainage, water exhausted, before you are ready to start the machine.
2, Check the amount of oil in the oil mist, the amount of oil should be between 1/3-2/3 of the oil cup, the shortage should be supplemented. Be sure to turn off the air source and evacuate the compressed air when replenishing the oil amount.
3, Lubricate the guide rail and screw, and wipe it clean with oil.
4, Start the power trial, check whether the sensors are normal, fastening bolts are safe and reliable.
Silicon steel sheet cross-cutting line using the working process.
1, Carefully and carefully read the drawing, enter the sheet width, sheet length and other data as required and review. Adjust the width of the guide rail, the position of the punching machine and the position of the stacking table according to the requirements.
2, Measure the actual width of the silicon steel coil to be cut, the measurement accuracy is 0.05 mm, check the width tolerance of the coil, S degree and waviness, all shall not exceed the standard.
3, On the material, manual trial shear, take the piece, compared with the drawings by checking the qualified before automatic shear.
4, Shear process operators to pay close attention to the transmission parts of the operating conditions, once the phenomenon of jamming, immediately stop to deal with.
5, The normal working process of the equipment, arms and other parts of the body do not reach into the pile of material under the table and other parts of the transmission, to prevent accidents, if necessary, adjustments should be made in the shutdown state.
6, Do not place tools, material pieces and other miscellaneous objects on the equipment when the equipment is running.
7, When using the crane to get on and off the material rolls, be sure to operate according to the regulations, to prevent accidents.
8, When lifting finished products, make sure to adjust the balance of the material table, start slowly and fall slowly to prevent injuries from slippery pieces.
9, The waste basket should be replaced in time when the waste is full.
10, During the work, if the equipment is abnormal, stop immediately, notify the equipment maintenance personnel, and make a record.
11, Fill in the handover record carefully when handing over the shift.
Silicon steel sheet cross-cutting line using the end of the work.
1, The power supply and gas source should be turned off at the end of the work.
2, The equipment wipes clean and clean around the equipment.
1, The power supply and gas source should be turned off at the end of the work.
2, The equipment wipes clean and clean around the equipment.
+86-137 0285 5825 
sales@kingreal.org
jet-clima