Working Principle of Cross Shear Machine
Transporting roll trolley will transport the aluminum coil to the main and vice uncoiler, start the main and vice uncoiler alignment cylinder, tighten the aluminum coil; start the initial guide plate lifting hydraulic cylinder, lift the initial guide plate, start the initial guide plate elastic hydraulic cylinder, turn over the aluminum coil; start the main and vice uncoiler to rotate the aluminum coil, so that the aluminum plate successfully through the initial guide plate out of the channel, into the now launched pinch feed roller equipment, the use of friction is the aluminum plate in turn through the straightening roller equipment. Roll equipment, cleaning equipment (clean aluminum plate on both sides of the oil stains aluminum powder, etc.), straightening machine (straightening), rotating flat shear (cut to size), belt conveyor (check the transport of aluminum plate), and finally enter the palletizing table, palletizing plate to size, by the palletizing trolley will be palletized aluminum plate pallets transported out.
The uncoiling line has "online operation" and "manual operation" modes.
The uncoiling line has "online operation" and "manual operation" modes.
In manual operation mode: every movement of the machine is controlled by the buttons and knobs on the operator panel. In manual mode, the machine can complete the work that requires manual participation, such as loading and unloading. In manual mode, each action of the machine can be controlled individually by the operator, which also facilitates the daily maintenance and fault judgment of the machine.
In the automatic operation mode, most of the movements of the machine are controlled automatically according to the pre-designed program, without manual participation, which simplifies the requirements for the machine operator and reduces the staffing and labor intensity of the workers.
These are the two modes of operation of the cross-cutting shear, in actual use can be selected independently according to the requirements.
In order to extend the service life of CNC horizontal shear machine, the general requirements to prevent direct sunlight and other thermal radiation, to prevent too wet, dusty or corrosive gas sites, to keep away from oscillating equipment, such as punching machines, forging equipment, etc., as far as possible, and these devices are placed at a certain interval, the conditions of the enterprise can be set up independently of the horizontal shear workshop.
The main features of the cross-cutting machine.
In order to extend the service life of CNC horizontal shear machine, the general requirements to prevent direct sunlight and other thermal radiation, to prevent too wet, dusty or corrosive gas sites, to keep away from oscillating equipment, such as punching machines, forging equipment, etc., as far as possible, and these devices are placed at a certain interval, the conditions of the enterprise can be set up independently of the horizontal shear workshop.
The main features of the cross-cutting machine.
Use: The equipment is processing transformer cores, welding machine cores, reactor cores of special equipment.
The choice of rotary flying shear using the active gear device, the choice of special alloy steel, heat-treated imported grinding machine, precision can be up to the new standard of more than 6 levels (old standard 1 level), can safely eliminate the impact sound when shearing. AC servo motor of the main drive motor for cutting. Control is by specially planned integrated module, the length measurement accuracy can reach ± 0.5 mm.
1. The machine is detected by precision grating, Delta AC servo system with Delta PLC professional module to achieve high precision fixed-length feeding to ensure shearing accuracy; the highest feeding speed of 60m/min, starting and braking time is less than 100ms.
2. Adopt intuitive human-machine interface with full Chinese control, the operator can easily complete the operation of piece shape selection and parameter correction through the touch screen.
3. computer for length compensation, rapid adjustment of shear length
4. Automatic completion of shearing, punching, counting, etc.
5. Width adjustment of the cross shear adopts the center positioning method.
1. The machine is detected by precision grating, Delta AC servo system with Delta PLC professional module to achieve high precision fixed-length feeding to ensure shearing accuracy; the highest feeding speed of 60m/min, starting and braking time is less than 100ms.
2. Adopt intuitive human-machine interface with full Chinese control, the operator can easily complete the operation of piece shape selection and parameter correction through the touch screen.
3. computer for length compensation, rapid adjustment of shear length
4. Automatic completion of shearing, punching, counting, etc.
5. Width adjustment of the cross shear adopts the center positioning method.
+86-137 0285 5825 
sales@kingreal.org
jet-clima